Mytee Spyder HP60 Bedienungsanleitung PDF herunterladen (Seite 7)

Setup

1. Open lid of solution tank. Fill solution with water or approved cleaning agent. For

best results, ll with warm water (140

Flammable materials can cause an explosion or re. Do not use ammable solutions

or materials in tank(s).

FOR SAFETY: When using machine, follow mixing and handling instructions on

chemical containers.

ATTENTION: If using powdered cleaning chemicals, mix prior to adding.

2. Attach solution hose (located front of machine). NOTE: Make sure the quick

disconnect snap together rmly. As you do this, always inspect hoses for cracks or

fraying. Do not use if hoses are damaged.

3. Attach other end of solution hose to wand.

4. Attach vacuum hose to recovery tank.

5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate

machine unless cord is properly grounded. FOR SAFETY: Do not operate machine

with the use of an extension cord.

6. Turn on pump. Key tool until you have a steady ow.

7. Release tool trigger. Turn on heater.

8. Wait 8–10 minutes for unit to pre-heat.

9. Re-key upholstery tool until hot water begins owing.

10. Once hot water is owing, release trigger and pre-heat an additional 4–5 minutes.

11. Turn on vacuum motor.

12. Begin cleaning. Make two dry passes to every wet pass.

13. For oor cleaning, unplug tool and attach oor wand.

14. Work away from cords to avoid damage.

15. Use a defoamer in your recovery tank.

16. To clean heavily soiled areas, repeat cleaning from different directions.

17. When oat shuts off vacuum, empty tanks.

18. When work is complete, unplug cords and hoses.

19. Wrap and clean hoses. Clean all tanks.

Pre-Operation

1. Vacuum carpet and upholstery and remove other debris.

2. Perform machine setup procedures.

3. Inspect power cord for damage.

Operation

1. Turn pump switch on.

2. Pull up on tool lever to release air in the line. Hold lever until a steady ow of water

comes out of the wand.

3. Once pump is primed and there is pressure in the solution line, turn on heater switch

(if model is equipped with heater) and wait a few minutes for water to heat up.

4. Once water is heated, turn on vacuum and begin cleaning.

Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.

1. Work away from outlet and power cord to prevent cord damage.

2. Use a recommended foam control solution in the recovery tank to prevent vacuum

motor damage. Periodically check for excessive foam buildup in solution tank, and

recovery tank.

3. To clean heavily soiled areas, repeat cleaning path from different direction.

4. When ball oat shuts off vacuum, it is time to empty the dirty water from the

recovery tank, and rell solution tank.

5. After cleaning, relieve water pressure from tool before disconnecting hose.

Squeeze trigger for ve seconds after turning main power switch off.

After Use

1. Unplug.

2. Empty solution tank and rinse it with clean water.

3. Inspect hoses and replace if damaged.

4. Inspect solution lter. Clean or replace if damaged.

5. Store the machine in a clean, dry place.

6. Open recovery tank cover to promote air circulation.

Maintenance Schedule

Maintenance item Daily Once a week

Clean and inspect Tanks

Clean and inspect Hoses

Check lters

Check power supply cable

Clean machine with all purpose cleaner and cloth

Check spray nozzles

Flush solution system with Mytee system maintainer

Remove and clean oat shut-off screen from tank

Inspect vacuum hoses for holes and loose cuffs

Trouble Shooting

There is no power.

1. Plug machine in proper outlet.

2. Check circuit breaker; reset circuit breaker, other items should not run on the

same circuit as machine. Outlet must be a 20-amp circuit.

Pump does not work properly.

1. Snap quick disconnects rmly together.

2. Check solution tank; may be empty.

3. Jets clogged, remove jet and ush clean.

4. Filters clogged, remove lters and rinse clean with water.

5. Heater is blocked; ush out with Mytee’s system maintainer.

6. If brass check valve is stuck replace valve.

7. Check pump wire. May need to reconnect wire.

8. Switch plate switch may need to be replaced.

9. If pump motor brushes are worn, replace pump.

Heater does not work properly.

1. If sensor mounted on the heater has popped, reset sensor by pushing in button.

2. Heating element may need to be replaced.

Vacuum motor does not work properly.

1. Check that hose is tightly connected.

2. Close drain hose valve completely.

3. Secure the vacuum tank tightly.

4. If ball oat is shut off, empty vacuum tank of all wastewater.

5. Make sure ball oat is rmly installed on the elbow.

6. If water is coming out of vacuum motor, use a low foaming detergent.

7. Clean upholstery tool or oor wand jets.

Accessories (optional)

2200 Airmover

3601 System Maintainer

2700 Mytee-Dry

8700 Crevice Tool

HP-Dry Vehicle Drying Kit

FAQs

Q: How much does the HP60 weigh and what are the shipping dimensions?

A: 69 Pounds - Box dimensions are 28 1/2” x 17 1/4” x 35 3/4”.

Must ship motor freight.

Q: What comes standard with the HP60?

A: The HP60 comes with a hose hanger ( H375 ), a 25’ 12/3 Cord, 15’ 1-1/4”

Vacuum/Solution Hose ( 8501 ), Cuff-Lynx™ 1-1/4” reducer ( H122 ) and a

3” Stainless Steel Upholstery Tool ( 8400 ).

Q: Does Mytee recommend a tool for the machine?

A: A variety of tools can be used with the unit, including our 8390 wand, 8700 crevice

tool, and 8400 upholstery tool. Also our HP-Dry kit can be used for drying interiors

and exteriors.

Q: Where do I plug the machine in?

A: The HP60 requires a 20A grounded circuit. Please note: GFI outlets may trip

before the breaker setting.

Q: What is the proper pre heat cycle for the HP60?

A: Turn pump switch to the on position and prime pump through the solution hose

and the tool. Then turn the heater switch to the on position. Let the machine sit idle

for 8-10 minutes. Spray tool until you feel the hot water from the jet. Let machine sit

idle for an additional 3-5 minutes. This will insure the water in the heater and hoses

will be at the hottest point to start cleaning.

GENERAL INFORMATION

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Mytee Spyder HP60 Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Staubsauger Mytee Spyder HP60